Plumbing referrals for Washington & nearby townsCall: (202) 915-7612
(202) 915-7612

Backflow Testing in Bowie, MD

plumberwashingtondc.net

Irrigation, fire sprinkler or boiler assembly in Bowie? Find out which utility's rules apply, then get it tested.

Backflow question in Bowie?
Call now to be connected with a local plumber in Bowie.
(202) 915-7612

Bowie is split between two water systems, and that decides who sets your backflow rules. In WSSC Water areas, testable assemblies must be tested every year by a WSSC-registered plumber who is a certified cross-connection technician; the City of Bowie's own water customers should check with the city water plant. Call the number on this page to be connected with a local plumber in Bowie.

Technician attaching a test kit to a backflow preventer assembly beside a tree-lined commercial building, backflow testing in Bowie, MD

Signs you need a backflow visit

  • A letter says a testable assembly at your address is due for its annual test
  • Water trickles from the relief port or a test cock when the sprinklers run
  • You bought a house with an in-ground irrigation system and no test history came with it
  • A previous test failed and nobody came back to repair and retest
  • You are adding sprinkler zones, a hose-fed fertilizer setup or a boiler with chemical treatment
  • The device is cracked, leaking at the unions or crusted with corrosion

How it works in Bowie

The City of Bowie runs its own water system, built by the Levitt Corporation in the early 1960s and serving roughly 7,900 customers in sections such as Somerset, Tulip Grove, Kenilworth, Yorktown, Whitehall and Overbrook. That system draws on wells in the Magothy, Patapsco and Patuxent aquifers. If your street is in one of those sections, ask the City water plant at 301-809-3060 what it expects for backflow assemblies before you assume a schedule.

The rest of Bowie is WSSC Water territory, so a neighbor a few streets away can be on a different system than you. There the WSSC Plumbing and Fuel Gas Code applies: testable assemblies on irrigation lines, residential fire sprinkler systems and chemically treated boilers get tested every year, and again after they are installed, repaired or moved. WSSC does not send its own staff to test; the owner hires a qualified plumber. In Prince George's County, plumbing permits come from WSSC, not the county.

Call now to be connected with a local plumber in Bowie.
(202) 915-7612

What affects the cost

  • Pass or fail. A clean pass is a short visit; a failed check or relief valve adds parts, labor and a retest.
  • Device type. An RPZ has more internal parts than a pressure vacuum breaker or double check.
  • Reachability. An assembly behind shrubs, in a tight utility room or inside a buried box takes longer.
  • Repair or replace. An older, corroded body may make a new assembly the better value.
  • Paperwork. Ask whether filing the result with the utility is included.

What happens when you call

The call reaches an independent plumber who works in Bowie. Say whether your water bill comes from the City of Bowie or WSSC, describe what the device protects, and have any letter you received nearby. If water is pouring from the assembly, close the irrigation shutoff or the main valve until the plumber arrives.

Backflow Testing questions in Bowie

How do I know which water utility serves my address?
Look at your water bill. Bowie sections such as Somerset, Tulip Grove, Kenilworth and Yorktown are on the City of Bowie system; most other parts of the city are on WSSC Water. If you are unsure, the City water plant at 301-809-3060 can tell you.
Who is allowed to test my backflow assembly?
In WSSC areas, only a plumber registered with WSSC Water who is also a certified cross-connection technician may test and repair testable assemblies. City of Bowie water customers should ask the city what it accepts.
Why does an in-ground sprinkler system need a backflow assembly?
Sprinkler heads sit in soil, fertilizer and standing water. If pressure in the main drops, that water can be pulled back into the house supply; the assembly stops it.
What happens if my assembly fails the test?
The plumber usually rebuilds the failing check or relief valve and retests. If the body is cracked or badly corroded, replacement is the usual answer, and in WSSC areas a new device is tested after installation.

More plumbing services in Bowie

Backflow Testing nearby

Call now to be connected with a local plumber in Bowie.
(202) 915-7612

Last updated:

☎ Call (202) 915-7612